“Handwork in Wood” – Wood Hand Tools Part One: Traditional Cutting Tool Concepts

Hand_Work_Cover.29970500_stdWe are starting a series of blog posts that will be from various “old but good” books on woodworking. The following comes from William Noyes’s book, Handwork in Wood. William Noyes, M.A. was an Assistant Professor in the Department of Industrial Arts at the Teachers College, Columbia University during the early 1900s.

From the Publisher

Originally published in 1910 as a manual for teachers of woodwork, William Noyes’ HANDWORK IN WOOD to this day ranks among the all time best, most complete and practical primers on the tools and techniques of good, old fashioned “no electricity needed” hand tool carpentry. Whether you are headed “off the grid” or just off to the garage, with over 300 photographs and illustrations, HANDWORK IN WOOD is the only book the modern handyman with a taste for Old World craftsmanship and style will ever need.

FOREWORD

This book is intended primarily for teachers of woodwork, but the author hopes that there will also be other workers in wood, professional and amateur, who will find in it matter of interest and profit.

Although an “old” book, one reviewer said it well: The author is clearly a master craftsman with an ability to explain what he knows. I am very impressed with this book both in the amount of information and the clarity of explanations. Much of it content is still relevant today. It certainly helped me to determine which tools I need to buy and some of the techniques for using them.

Without further ado…

Chapter IV. Part One.

WOOD HAND TOOLS

The hand tools in common use in woodworking shops may, for convenience, be divided into the following classes: 1, Cutting; 2, Boring; 3, Chopping; 4, Scraping; 5, Pounding; 6, Holding; 7, Measuring and Marking; 8, Sharpening; 9, Cleaning.

1. CUTTING TOOLS.

The most primitive as well as the simplest of all tools for the dividing of wood into parts, is the wedge. The wedge does not even cut the wood, but only crushes enough of it with its edge to allow its main body to split the wood apart. As soon as the split has begun, the edge of the wedge serves no further purpose, but the sides bear against the split surfaces of the wood. The split runs ahead of the wedge as it is driven along until the piece is divided.

It was by means of the wedge that primitive people obtained slabs of wood, and the great change from primitive to civilized methods in manipulating wood consists in the substitution of cutting for splitting, of edge tools for the wedge. The wedge follows the grain of the wood, but the edge tool can follow a line determined by the worker. The edge is a refinement and improvement upon the wedge and enables the worker to be somewhat independent of the natural grain of the wood.

In general, it may be said that the function of all cutting tools is to separate one portion of material from another along a definite path. All such tools act, first, by the keen edge dividing the material into two parts; second, by the wedge or the blade forcing these two portions apart. If a true continuous cut is to be made, both of these actions must occur together. The edge must be sharp enough to enter between the small particles of material, cutting without bruising them, and the blade of the tool must constantly force apart the two portions in order that the cutting action of the edge may continue.

The action of an ax in splitting wood is not a true cut, for only the second process is taking place, Fig. 59. The split which opens in front of the cutting edge anticipates its cutting and therefore the surfaces of the opening are rough and torn.

059-276

Fig. 59. Wedge Action.

060-296

Fig. 60. Edge Action.

When a knife or chisel is pressed into a piece of wood at right angles to the grain, and at some distance from the end of the wood, as in Fig. 60, a continuous cutting action is prevented, because soon the blade cannot force apart the sides of the cut made by the advancing edge, and the knife is brought to rest. In this case, it is practically only the first action which has taken place.

Both the actions, the cutting and the splitting, must take place together to produce a true continuous cut. The edge must always be in contact with the solid material, and the blade must always be pushing aside the portions which have been cut. This can happen only when the material on one side of the blade is thin enough and weak enough to be readily bent out of the way without opening a split in front of the cutting edge. This cutting action may take place either along the grain, Fig. 61, or across it, Fig. 62.

The bending aside of the shaving will require less force the smaller the taper of the wedge. On the other hand, the wedge must be strong enough to sustain the bending resistance and also to support the cutting edge. In other words, the more acute the cutting edge, the easier the work, and hence the wedge is made as thin as is consistent with strength. This varies all the way from hollow ground razors to cold-chisels. For soft wood, the cutting angle (or bevel, or bezel) of chisels, gouges and plane-irons, is small, even as low as 20°; for hard wood, it must be greater. For metals, it varies from 54° for wrought iron to 66° for gun metal.

061-300

Fig. 61. Edge and Wedge Action With the Grain.

060-296

Fig. 62. Edge and Wedge Action Across the Grain.

Ordinarily a cutting tool should be so applied that the face nearest the material lies as nearly as possible in the direction of the cut desired, sufficient clearance being necessary to insure contact of the actual edge.

There are two methods of using edge tools: one, the chisel or straight cut, by direct pressure; the other, the knife or sliding cut.

The straight cut, Fig. 63, takes place when the tool is moved into the material at right angles to the cutting edge. Examples are: the action of metalworking tools and planing machines, rip-sawing, turning, planing (when the plane is held parallel to the edge of the board being planed), and chiseling, when the chisel is pushed directly in line with its length.

The knife or sliding cut, Fig. 64, takes place when the tool is moved forward obliquely to its cutting edge, either along or across the grain. It is well illustrated in cutting soft materials, such as bread, meat, rubber, cork, etc. It is an advantage in delicate chiseling and gouging. That this sliding action is easier than the straight pressure can easily be proved with a penknife on thin wood, or by planing with the plane held at an angle to, rather than in line with, the direction of the planing motion. The edge of the cutter then slides into the material. The reason why the sliding cut is easier, is partly because the angle of the bevel with the wood is reduced by holding the tool obliquely, and partly because even the sharpest cutting edge is notched with very fine teeth all along its edge so that in the sliding cut it acts like a saw. In an auger-bit, both methods of cutting take place at once. The scoring nib cuts with a sliding cut, while the cutting lip is thrust directly into the wood.

063-130

Fig. 63. Straight Cut.

064-250

Fig. 64. Sliding Cut.

The chisel and the knife, one with the edge on the end, and the other with the edge on the side, are the original forms of all modern cutting tools.

Noyes, W. (1910). Chapter IV. WOOD HAND TOOLS. In Handwork in Wood (pp. 51-53). Peoria, Ill.: Manual Arts Press

Stay tuned for the upcoming blogs.

One Response to “Handwork in Wood” – Wood Hand Tools Part One: Traditional Cutting Tool Concepts

  1. Larry Chandler September 26, 2014 at 9:06 AM #

    Great idea and wonderful slightly different but super perspective.
    Note to Frank Strazza that last week I completed my third commissioned work to tear down and rebuild some high end older furniture. In each case I found that my simple mahogany wedges were the tool of choice to break away old wood joints with a minimum of damage to the wood. Using my wood mallet and hand made wedges has proven to be a winner. It didn’t dawn on me until this article that it has been the tool of choice for millennium. Thanks again for the articles.

    Larry Chandler